Last login: Tue May 12 22:24:30 on ttys001 MacBook-van-Richard:~ Richard$ telnet 192.168.1.92 Trying 192.168.1.92... Connected to 192.168.1.92. Escape character is '^]'. root dreambox openpli 4 et6x00 et6x00 login: root dreambox root@et6x00:~# dreambox -sh: dreambox: not found root@et6x00:~# root@et6x00:~# lsusb Bus 002 Device 002: ID 1a40:0101 Bus 001 Device 001: ID 1d6b:0002 Bus 002 Device 001: ID 1d6b:0002 Bus 003 Device 001: ID 1d6b:0001 Bus 004 Device 001: ID 1d6b:0001 root@et6x00:~# root@et6x00:~# dmesg bmem: adding 32 MB LINUX region at 7 MB (0x02023000@0x007dd000) bmem: adding 216 MB RESERVED region at 40 MB (0x0d800000@0x02800000) bmem: adding 256 MB LINUX region at 512 MB (0x10000000@0x20000000) Zone ranges: Normal [mem 0x00000000-0x2fffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00000000-0x0fffffff] node 0: [mem 0x20000000-0x2fffffff] On node 0 totalpages: 131072 Normal zone: 1024 pages used for memmap Normal zone: 0 pages reserved Normal zone: 130048 pages, LIFO batch:31 Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes PERCPU: Embedded 7 pages/cpu @81407000 s6272 r8192 d14208 u32768 pcpu-alloc: s6272 r8192 d14208 u32768 alloc=8*4096 pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: bmem=216M ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs console=null consoleblank=0 PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) __ex_table already sorted, skipping sort Memory: 290468k/524288k available (6140k kernel code, 233820k reserved, 1528k data, 260k init, 0k highmem) Hierarchical RCU implementation. NR_IRQS:160 Measuring MIPS counter frequency... Detected MIPS clock frequency: 405 MHz (202.500 MHz counter) Console: colour dummy device 80x25 Calibrating delay loop... 401.40 BogoMIPS (lpj=200704) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 SMP: Booting CPU1... CPU revision is: 0002a044 (Brcm4380) FPU revision is: 00130001 Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes SMP: CPU1 is running Brought up 2 CPUs devtmpfs: initialized NET: Registered protocol family 16 USB0: power enable is active low; overcurrent is active low PCI2.3->SDRAM window: 512 MB bio: create slab at 0 SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Linux video capture interface: v2.00 Advanced Linux Sound Architecture Driver Initialized. PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff] pci_bus 0000:00: root bus resource [io 0x0400-0x83ff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 PCI host bridge to bus 0000:01 pci_bus 0000:01: root bus resource [mem 0x10510000-0x1051ffff] pci_bus 0000:01: root bus resource [io 0x8400-0x87ff] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] pci 0000:01:00.0: [14e4:8602] type 00 class 0x01010f PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42) pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff] pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref] Bluetooth: Core ver 2.16 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized cfg80211: Calling CRDA to update world regulatory domain Switching to clocksource upg FS-Cache: Loaded NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 64 NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered fuse init (API version 7.20) msgmni has been set to 567 io scheduler noop registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A loop: module loaded sata_brcmstb 0000:01:00.0: version 4.0 __clk_enable: sata [1] PCI: Enabling device 0000:01:00.0 (0000 -> 0003) sata_brcmstb 0000:01:00.0: setting latency timer to 64 scsi0 : sata_brcmstb scsi1 : sata_brcmstb ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42 ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42 Broadcom STB NAND controller (BrcmNand Controller) bcmemac: Broadcom STB 10/100 EMAC driver v3.0 bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:03:f9:95) bcmemac: not registering interface #1 at 0x10090000 (no PHY detected) usbcore: registered new interface driver zd1201 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver __clk_enable: usb [1] ehci-brcm ehci-brcm.0: Broadcom STB EHCI ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300 ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ehci-brcm ehci-brcm.1: Broadcom STB EHCI ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2 ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500 ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-brcm ohci-brcm.0: Broadcom STB OHCI ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3 ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ohci-brcm ohci-brcm.1: Broadcom STB OHCI ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4 ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mousedev: PS/2 mouse device common for all mice i2c /dev entries driver usbcore: registered new interface driver btusb usbcore: registered new interface driver usbhid usbhid: USB HID core driver TCP: cubic registered NET: Registered protocol family 17 Bluetooth: HIDP (Human Interface Emulation) ver 1.2 Bluetooth: HIDP socket layer initialized Key type dns_resolver registered EBI CS1: setting up NAND flash (primary) mtd->oobsize=0, mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000000 B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1 brcmnand_read_id: CS1: dev_id=ecf10095 After: NandSelect=50000200, nandConfig=15142200 Block size=00020000, erase shift=17 NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11 busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff timing1 not adjusted: 5363444f timing2 not adjusted: 00000fc6 eccLevel=15, 1Ksector=0, oob=16 nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000 BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1 Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6 BrcmNAND version = 0x0302 128MB @00000000 B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1 brcmnand_read_id: CS1: dev_id=ecf10095 After: NandSelect=50000200, nandConfig=15142200 Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0 brcmnand_scan: B4 nand_select = 50000200 brcmnand_scan: After nand_select = 50000200 page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17 Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000 ECC layout=brcmnand_oob_bch4_4k brcmnand_scan: mtd->oobsize=64 brcmnand_scan: oobavail=50, eccsize=512, writesize=2048 brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS1 Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS1 Adjust partition complete size from entire device to 7f00000 to avoid overlap with BBT reserved space Adjust partition rootfs size from entire device to 7900000 to avoid overlap with BBT reserved space Creating 3 MTD partitions on "brcmnand.0": 0x000000000000-0x000007f00000 : "complete" 0x000000000000-0x000000600000 : "kernel" 0x000000600000-0x000007f00000 : "rootfs" PM: CP0 COUNT/COMPARE frequency depends on divisor UBI: attaching mtd2 to ubi0 ata1: SATA link down (SStatus 4 SControl 300) usb 2-1: new high-speed USB device number 2 using ehci-brcm hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected ata2: SATA link down (SStatus 4 SControl 300) UBI: scanning is finished UBI: attached mtd2 (name "rootfs", size 121 MiB) to ubi0 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 968, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1268557079 UBI: available PEBs: 0, total reserved PEBs: 968, PEBs reserved for bad PEB handling: 20 UBI: background thread "ubi_bgt0d" started, PID 49 ALSA device list: No soundcards found. Warning: unable to open an initial console. UBIFS: background thread "ubifs_bgt0_0" started, PID 50 UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 0, name "rootfs"(null) UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 118468608 bytes (112 MiB, 933 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs) UBIFS: reserved for root: 0 bytes (0 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2F8BB50D-CA68-43E8-B166-3B16A0371DFA, small LPT model VFS: Mounted root (ubifs filesystem) on device 0:10. devtmpfs: mounted Freeing unused kernel memory: 260k freed usbcore: registered new interface driver tpm root@et6x00:~#