foutmelding E-1D

[Gast]

Wie weet wat deze foutmelding inhoud??kreeg hummy om te patchen maar gaf al melding ra aan,accepteerd wel nieuwe soft maar geen freq lijst wie helpt??

[Hagkobe]

<B>E-Id</B> <A HREF="http://null" TARGET=_blank>null</A><BR> Downloading to incorrect model (system ID does not match)<BR> Download the correct software for your Humax model.<BR> <BR>E-bF E-Hn<BR> Downloading incorrect software for this Hardware<BR> Non-Superset software download to a Superset or vice versa<BR> Download the correct software for the hardware type you have.<BR> <BR>E-ut<BR> UART RX/TX timed out <BR> Incorrect Baud Rate set on PC<BR> Try changing the Baud rate you are sending to the receiver/decoder if this fails then power off both PC and Humax and re-try download.<BR> <BR>E-hF<BR> Invalid HDF file format<BR> Non-software file downloaded (e.g. a Formula1 file)<BR> Use the correct software file. Download a new version, if this fails, contact Humax.<BR> <BR>E-HC E-bC E-dC<BR> Incorrect header block (CRC-16)<BR> The software was corrupted during the download.<BR> Download the software again, from the Humax website<BR> <BR>E-AC<BR> Incorrect application CRC-32<BR> You have an old version of the software<BR> Download latest version of application S/W<BR> <BR>E-Ad<BR> Invalid address<BR> There is a problem with the software<BR> Inform Humax - they will release a new version as soon as possible<BR> <BR>E-Ao<BR> Invalid offset address<BR> There is a problem with the software<BR> Inform Humax - they will release a new version as soon as possible<BR> <BR>E-Ft<BR> Flash program timeout<BR> Flash memory in your Humax is damaged<BR> Try the download again. If this fails the flash memory will need replacing, talk to your dealer, or to Humax<BR> <BR>E-It E-Et<BR> EEPROM program timeout<BR> EEPROM id damaged<BR> Try the download again. If this fails the flash memory will need replacing, talk to your dealer, or to Humax<BR> <BR>E-FE<BR> Flash memory compare failure<BR> Flash memory is damaged<BR> Try the download again. If this fails the flash memory will need replacing, talk to your dealer, or to Humax<BR> <BR>E-Fn<BR> Invalid Flash device<BR> Flash memory is defective<BR> Try the download again. If this fails the flash memory will need replacing, talk to your dealer, or to Humax<BR> <BR>E-AS<BR> Incorrect application size<BR> Size does not match expected value<BR> Confirm the version and software is correct for your hardware. Download a new version and try again.<BR> <BR>

[Gast]

Blijf foutmelding houden kan geen andere orginele soft overheen blijft IDENTITEITSCRISIS houden (rijp voor sloop????)<BR>grtz hendrik b

[Gast]

Vertel even WELKE Humax het is en geef even de info aand die je onder STB Status kunt opvragen... Maakt het voor ons ook wat makkelijker...<P>Gaat de Humax soms toevallig *uit* na de rA melding?? Zo ja, dan kun je heel waarschijlijk elco C15/C16 en C9 gaan vervangen. (Even meten op J7/J10) moet 8.2 tot 8.6V geven.

[Gast]

Humax IRCI 5400<BR>mainboard oak II-L<BR>geeft aan bij opstarten L208<BR>daarna RA<BR>dan zit hij net zo vast als een huis kun je er geen kant meer mee op.ja uitzetten maar voor de rest helemaal niks meer.