infinity smartmouse (USB) op Ubuntu 7.04 PC

[Hannibal2206]

Hallo,

 

Ik draai al een tijdje CCcam op een Ubuntu 7.04 PC, als vervanging van mijn NSLU2 (die werd te licht met meerdere opnames tegelijk en klein qua capaciteit).

 

Ik probeer nu ook de Infinity Smartmouse (USB) hierop aan te sluiten voor mijn Seca2 C+ kaartje, maar dat lukt nog niet erg

 

Wie kan me een beetje op weg helpen ?

 

De smartmouse wordt wel gezien als USB device:

 

han@ubuntu:~$ uname -a

Linux ubuntu 2.6.20-15-server #2 SMP Sun Apr 15 07:41:34 UTC 2007 i686 GNU/Linux

han@ubuntu:~$ lsusb

Bus 001 Device 002: ID 104f:0002

Bus 001 Device 001: ID 0000:0000

han@ubuntu:~

[wian]

Hallo Han. Ik heb geen ervaring met Ubuntu, maar je hebt in ieder geval een recente kernel. Het kan zijn dat je de kernel sources moet downloaden en deze moet aanpassen, maar misschien heb je met deze nieuwe kernel geluk.

 

Je kunt proberen:

 

modprobe usbserial

modprobe ftdi_sio

 

met dmesg kun je kijken naar het resultaat, als je geluk hebt ziet het er zo uit:

 

---

kernel: usbcore: registered new driver usbserial

kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for generic

kernel: usbcore: registered new driver usbserial_generic

kernel: drivers/usb/serial/usb-serial.c: USB Serial Driver corekernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device

kernel: drivers/usb/serial/ftdi_sio.c: Detected FT232BM

kernel: drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver

---

 

Je hebt er nu een device bijgekregen, bijvoorbeeld /dev/ttyUSB0.

 

Ik gebruik zelf newcs, maar met CCcam zou het ook geen probleem moeten zijn. Voeg in CCcam.cfg de nieuwe cardreader toe:

 

SERIAL READER : /dev/ttyUSB0 mouse

 

(je kan ipv mouse ook phoenix of uniprog proberen)

 

Op de site van WBE staat het programma smusbutil. Hiermee kun je de smartmouse in phoenix mode zetten en de clocksnelheid aanpassen (6mhz ipv 3,58). Bij mij werkt het programma niet (compileert goed en start zonder foutmeldingen, maar doet uiteindelijk niets) en toch werkt newcs zonder problemen. Als je echter een irdeto2 kaart hebt, heb je dit programma nodig om de smartmouse in 6mhz mode te zetten.

 

Als het niet werkt, geef dan de output van de modprobe commando's en de output van dmesg, dan kunnen we met je meedenken. Succes!

[Hannibal2206]

Ik krijg wel een device /dev/ttyUSB0, maar CCcam doet er nog niets mee.

 

 

root@ubuntu:/data/dreambox# modprobe -v usbserial

insmod /lib/modules/2.6.20-15-server/kernel/drivers/usb/serial/usbserial.ko

root@ubuntu:/data/dreambox# modprobe -v ftdi_sio

insmod /lib/modules/2.6.20-15-server/kernel/drivers/usb/serial/ftdi_sio.ko

 

root@ubuntu:/data/dreambox# dmesg

[ 0.010023] Brought up 2 CPUs

[ 0.170414] migration_cost=1474

[ 0.171564] Booting paravirtualized kernel on bare hardware

[ 0.171892] Time: 11:27:31 Date: 07/03/107

[ 0.172055] NET: Registered protocol family 16

[ 0.172527] EISA bus registered

[ 0.172555] ACPI: bus type pci registered

[ 0.174986] PCI: PCI BIOS revision 2.10 entry at 0xfb5c0, last bus=1

[ 0.174998] PCI: Using configuration type 1

[ 0.175007] Setting up standard PCI resources

[ 0.185656] mtrr: your CPUs had inconsistent fixed MTRR settings

[ 0.185670] mtrr: probably your BIOS does not setup all CPUs.

[ 0.185680] mtrr: corrected configuration.

[ 0.198384] ACPI: Interpreter enabled

[ 0.198406] ACPI: Using IOAPIC for interrupt routing

[ 0.201378] ACPI: PCI Root Bridge [PCI0] (0000:00)

[ 0.201401] PCI: Probing PCI hardware (bus 00)

[ 0.201704] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0

[ 0.202916] * Found PM-Timer Bug on the chipset. Due to workarounds for a bug,

[ 0.202925] * this clock source is slow. Consider trying other clock sources

[ 0.203006] PCI quirk: region 4000-403f claimed by PIIX4 ACPI

[ 0.203020] PCI quirk: region 5000-500f claimed by PIIX4 SMB

[ 0.203089] PCI: Firmware left 0000:00:09.0 e100 interrupts enabled, disabling

[ 0.203515] Boot video device is 0000:00:0f.0

[ 0.204036] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]

[ 0.214199] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.

[ 0.215359] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)

[ 0.216491] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)

[ 0.217653] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 *12 14 15)

[ 0.225511] Linux Plug and Play Support v0.97 © Adam Belay

[ 0.225573] pnp: PnP ACPI init

[ 0.235745] pnp: PnP ACPI: found 8 devices

[ 0.235773] PnPBIOS: Disabled by ACPI PNP

[ 0.236067] PCI: Using ACPI for IRQ routing

[ 0.236084] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report

[ 0.238355] NET: Registered protocol family 8

[ 0.238367] NET: Registered protocol family 20

[ 0.238420] NetLabel: Initializing

[ 0.238429] NetLabel: domain hash size = 128

[ 0.238437] NetLabel: protocols = UNLABELED CIPSOv4

[ 0.238500] NetLabel: unlabeled traffic allowed by default

[ 0.242488] PCI: Bridge: 0000:00:01.0

[ 0.242502] IO window: disabled.

[ 0.242516] MEM window: disabled.

[ 0.242527] PREFETCH window: disabled.

[ 0.242710] NET: Registered protocol family 2

[ 0.350283] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.350727] TCP established hash table entries: 16384 (order: 5, 131072 bytes)

[ 0.351480] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)

[ 0.352044] TCP: Hash tables configured (established 16384 bind 8192)

[ 0.352060] TCP reno registered

[ 0.390565] checking if image is initramfs... it is

[ 2.800714] Freeing initrd memory: 6640k freed

[ 2.802791] audit: initializing netlink socket (disabled)

[ 2.802845] audit(1186140453.590:1): initialized

[ 2.803595] VFS: Disk quotas dquot_6.5.1

[ 2.803705] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[ 2.803934] io scheduler noop registered

[ 2.803950] io scheduler anticipatory registered

[ 2.803960] io scheduler deadline registered (default)

[ 2.804026] io scheduler cfq registered

[ 2.804057] Limiting direct PCI/PCI transfers.

[ 2.805242] isapnp: Scanning for PnP cards...

[ 3.162854] isapnp: No Plug & Play device found

[ 3.376614] Real Time Clock Driver v1.12ac

[ 3.376884] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled

[ 3.381353] mice: PS/2 mouse device common for all mice

[ 3.384592] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize

[ 3.385383] input: Macintosh mouse button emulation as /class/input/input0

[ 3.385591] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2

[ 3.385610] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

[ 3.386382] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1

[ 3.386399] PNP: PS/2 controller doesn't have AUX irq; using default 12

[ 3.639899] serio: i8042 KBD port at 0x60,0x64 irq 1

[ 3.640441] EISA: Probing bus 0 at eisa.0

[ 3.640499] Cannot allocate resource for EISA slot 4

[ 3.640511] Cannot allocate resource for EISA slot 5

[ 3.640550] EISA: Detected 0 cards.

[ 3.670968] TCP cubic registered

[ 3.671035] NET: Registered protocol family 1

[ 3.671160] Starting balanced_irq

[ 3.671231] Using IPI No-Shortcut mode

[ 3.671630] ACPI: (supports S0 S1 S4 S5)

[ 3.671837] Magic number: 3:328:478

[ 3.674416] Freeing unused kernel memory: 328k freed

[ 3.679535] Time: tsc clocksource has been installed.

[ 3.687894] input: AT Translated Set 2 keyboard as /class/input/input1

[ 4.521092] Capability LSM initialized

[ 4.713800] ACPI: Fan [FAN] (on)

[ 4.740858] ACPI: Expecting a [Reference] package element, found type DEFF5EAC

[ 4.740936] ACPI: Invalid passive threshold

[ 4.742648] ACPI: Thermal Zone [THRM] (41 C)

[ 6.978284] SCSI subsystem initialized

[ 6.986975] Adaptec aacraid driver (1.1-5[2423]-mh3)

[ 6.987167] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 17 (level, low) -> IRQ 16

[ 7.165849] usbcore: registered new interface driver usbfs

[ 7.166023] usbcore: registered new interface driver hub

[ 7.170821] usbcore: registered new device driver usb

[ 7.190229] e100: Intel® PRO/100 Network Driver, 3.5.17-k2-NAPI

[ 7.190253] e100: Copyright© 1999-2006 Intel Corporation

[ 7.249653] USB Universal Host Controller Interface driver v3.0

[ 7.326074] AAC0: kernel 4.2-1[7368]

[ 7.326093] AAC0: monitor 4.2-1[7368]

[ 7.326105] AAC0: bios 4.2-1[7368]

[ 7.326114] AAC0: serial 3d753

[ 7.355131] scsi0 : aacraid

[ 7.356135] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 18 (level, low) -> IRQ 17

[ 7.356606] scsi 0:0:0:0: Direct-Access Adaptec R5-1.5TB V1.0 PQ: 0 ANSI: 2

[ 7.412814] sym0: <896> rev 0x5 at pci 0000:00:0b.0 irq 17

[ 7.415220] sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking

[ 7.421992] sym0: SCSI BUS has been reset.

[ 7.422058] scsi1 : sym-2.2.3

[ 7.422657] ACPI: PCI Interrupt 0000:00:0b.1 -> GSI 19 (level, low) -> IRQ 18

[ 7.477527] sym1: <896> rev 0x5 at pci 0000:00:0b.1 irq 18

[ 7.479698] sym1: No NVRAM, ID 7, Fast-40, LVD, parity checking

[ 7.486480] sym1: SCSI BUS has been reset.

[ 7.486498] scsi2 : sym-2.2.3

[ 7.487174] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 19 (level, low) -> IRQ 18

[ 7.578935] e100: eth0: e100_probe: addr 0xdc106000, irq 18, MAC addr 00:02:B3:36:F6:31

[ 7.579277] ACPI: PCI Interrupt 0000:00:07.2[D] -> GSI 19 (level, low) -> IRQ 18

[ 7.579328] uhci_hcd 0000:00:07.2: UHCI Host Controller

[ 7.579777] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1

[ 7.579846] uhci_hcd 0000:00:07.2: irq 18, io base 0x0000c000

[ 7.580434] usb usb1: configuration #1 chosen from 1 choice

[ 7.580560] hub 1-0:1.0: USB hub found

[ 7.580605] hub 1-0:1.0: 2 ports detected

[ 7.614868] SCSI device sda: 2929717248 512-byte hdwr sectors (1500015 MB)

[ 7.614888] sda: assuming Write Enabled

[ 7.614898] sda: assuming drive cache: write through

[ 7.617123] SCSI device sda: 2929717248 512-byte hdwr sectors (1500015 MB)

[ 7.617142] sda: assuming Write Enabled

[ 7.617151] sda: assuming drive cache: write through

[ 7.617224] sda: sda1

[ 7.631933] sd 0:0:0:0: Attached scsi removable disk sda

[ 7.656834] sd 0:0:0:0: Attached scsi generic sg0 type 0

[ 7.699758] PIIX4: IDE controller at PCI slot 0000:00:07.1

[ 7.699833] PIIX4: chipset revision 1

[ 7.699844] PIIX4: not 100% native mode: will probe irqs later

[ 7.699875] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio

[ 7.699932] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio

[ 7.699975] Probing IDE interface ide0...

[ 7.988812] usb 1-1: new full speed USB device using uhci_hcd and address 2

[ 8.018963] hda: ST36421A, ATA DISK drive

[ 8.201179] usb 1-1: configuration #1 chosen from 1 choice

[ 8.748990] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

[ 8.749224] Probing IDE interface ide1...

[ 9.378720] HPT366: onboard version of chipset, pin1=1 pin2=2

[ 9.378743] HPT366: IDE controller at PCI slot 0000:00:13.0

[ 9.378773] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 17

[ 9.378820] HPT366: chipset revision 1

[ 9.378849] HPT366: 100% native mode on irq 17

[ 9.378887] ide2: BM-DMA at 0xd800-0xd807, BIOS settings: hde:pio, hdf:pio

[ 9.378939] ACPI: PCI Interrupt 0000:00:13.1 -> GSI 18 (level, low) -> IRQ 17

[ 9.378991] ide3: BM-DMA at 0xe400-0xe407, BIOS settings: hdg:pio, hdh:pio

[ 9.379031] Probing IDE interface ide2...

[ 9.408945] libata version 2.20 loaded.

[ 9.988623] Probing IDE interface ide3...

[ 10.627777] hda: max request size: 128KiB

[ 10.628716] hda: 12596850 sectors (6449 MB) w/256KiB Cache, CHS=13330/15/63, UDMA(33)

[ 10.628744] hda: cache flushes not supported

[ 10.628954] hda: hda1 hda2 < hda5 >

[ 11.460668] Attempting manual resume

[ 11.460686] swsusp: Resume From Partition 3:5

[ 11.460694] PM: Checking swsusp image.

[ 11.491427] PM: Resume from disk failed.

[ 11.598557] kjournald starting. Commit interval 5 seconds

[ 11.598603] EXT3-fs: mounted filesystem with ordered data mode.

[ 17.917541] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex

[ 20.045403] NET: Registered protocol family 10

[ 20.045902] lo: Disabled Privacy Extensions

[ 21.283345] Linux agpgart interface v0.102 © Dave Jones

[ 21.323669] pci_hotplug: PCI Hot Plug PCI Core version: 0.5

[ 21.339178] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4

[ 21.362057] agpgart: Detected an Intel 440BX Chipset.

[ 21.369137] agpgart: AGP aperture is 64M @ 0xd0000000

[ 21.472193] piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device

[ 22.286188] input: PC Speaker as /class/input/input2

[ 23.332615] lp: driver loaded but no devices found

[ 23.696826] Adding 321260k swap on /dev/disk/by-uuid/f0c5bf20-0bf2-414d-bfae-46e3b2dcd8a8. Priority:-1 extents:1 across:321260k

[ 23.936850] EXT3 FS on hda1, internal journal

[ 24.607617] kjournald starting. Commit interval 5 seconds

[ 24.607690] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended

[ 24.652037] EXT3 FS on sda1, internal journal

[ 24.652068] EXT3-fs: mounted filesystem with ordered data mode.

[ 30.095496] eth0: no IPv6 routers present

[ 45.234408] out of order segment: rcv_next BD442140 seq BD442148 - BD442181

[ 45.497762] ofo requeuing : rcv_next BD442148 seq BD442148 - BD442181

[ 60.393094] out of order segment: rcv_next BD44220A seq BD442212 - BD4422C5

[ 60.620413] ofo requeuing : rcv_next BD442212 seq BD442212 - BD4422C5

[ 1787.399950] usbcore: registered new interface driver usbserial

[ 1787.400039] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic

[ 1787.513369] usbcore: registered new interface driver usbserial_generic

[ 1787.513398] drivers/usb/serial/usb-serial.c: USB Serial Driver core

[ 1797.710343] drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device

[ 1797.710514] usbcore: registered new interface driver ftdi_sio

[ 1797.710531] drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver

[ 1806.025477] out of order segment: rcv_next 5848E873 seq 5848E8BA - 5848E8C2

[ 1806.052360] ofo packet was already received

 

 

 

lsusb output:

 

han@ubuntu:~$ lsusb -v

 

 

Bus 001 Device 002: ID 104f:0002

Device Descriptor:

bLength 18

bDescriptorType 1

bcdUSB 1.10

bDeviceClass 0 (Defined at Interface level)

bDeviceSubClass 0

bDeviceProtocol 0

bMaxPacketSize0 8

idVendor 0x104f

idProduct 0x0002

bcdDevice 4.00

iManufacturer 1 WB Electronics ApS

iProduct 2 Smartmouse USB

iSerial 0

bNumConfigurations 1

Configuration Descriptor:

bLength 9

bDescriptorType 2

wTotalLength 32

bNumInterfaces 1

bConfigurationValue 1

iConfiguration 0

bmAttributes 0x80

(Bus Powered)

MaxPower 100mA

Interface Descriptor:

bLength 9

bDescriptorType 4

bInterfaceNumber 0

bAlternateSetting 0

bNumEndpoints 2

bInterfaceClass 255 Vendor Specific Class

bInterfaceSubClass 255 Vendor Specific Subclass

bInterfaceProtocol 255 Vendor Specific Protocol

iInterface 2 Smartmouse USB

Endpoint Descriptor:

bLength 7

bDescriptorType 5

bEndpointAddress 0x81 EP 1 IN

bmAttributes 2

Transfer Type Bulk

Synch Type None

Usage Type Data

wMaxPacketSize 0x0040 1x 64 bytes

bInterval 0

Endpoint Descriptor:

bLength 7

bDescriptorType 5

bEndpointAddress 0x02 EP 2 OUT

bmAttributes 2

Transfer Type Bulk

Synch Type None

Usage Type Data

wMaxPacketSize 0x0040 1x 64 bytes

bInterval 0

Device Status: 0x0000

(Bus Powered)

 

Bus 001 Device 001: ID 0000:0000

Device Descriptor:

bLength 18

bDescriptorType 1

bcdUSB 1.10

bDeviceClass 9 Hub

bDeviceSubClass 0 Unused

bDeviceProtocol 0 Full speed hub

bMaxPacketSize0 64

idVendor 0x0000

idProduct 0x0000

bcdDevice 2.06

iManufacturer 3 Linux 2.6.20-15-server uhci_hcd

iProduct 2 UHCI Host Controller

iSerial 1 0000:00:07.2

bNumConfigurations 1

Configuration Descriptor:

bLength 9

bDescriptorType 2

wTotalLength 25

bNumInterfaces 1

bConfigurationValue 1

iConfiguration 0

bmAttributes 0xe0

Self Powered

Remote Wakeup

MaxPower 0mA

Interface Descriptor:

bLength 9

bDescriptorType 4

bInterfaceNumber 0

bAlternateSetting 0

bNumEndpoints 1

bInterfaceClass 9 Hub

bInterfaceSubClass 0 Unused

bInterfaceProtocol 0 Full speed hub

iInterface 0

Endpoint Descriptor:

bLength 7

bDescriptorType 5

bEndpointAddress 0x81 EP 1 IN

bmAttributes 3

Transfer Type Interrupt

Synch Type None

Usage Type Data

wMaxPacketSize 0x0002 1x 2 bytes

bInterval 255

Hub Descriptor:

bLength 9

bDescriptorType 41

nNbrPorts 2

wHubCharacteristic 0x000a

No power switching (usb 1.0)

Per-port overcurrent protection

bPwrOn2PwrGood 1 * 2 milli seconds

bHubContrCurrent 0 milli Ampere

DeviceRemovable 0x00

PortPwrCtrlMask 0xff

Hub Port Status:

Port 1: 0000.0103 power enable connect

Port 2: 0000.0100 power

Device Status: 0x0003

Self Powered

Remote Wakeup Enabled

[wian]

Heb je de CCcam.cfg aangepast? Heb je zowel mouse, uniprog als phoenix geprobeerd? Als je CCcam handmatig start met de -d optie, zie je dan dat ie probeert /dev/ttyUSB0 te openen? Bijvoorbeeld:

 

/var/bin/CCcam.x86 -tvd

[Hannibal2206]

hoe moet die regel in CCcam.cfg er precies uitzien ?

 

Ik heb nu alleen "PHOENIX READER PATH : /dev/ttyUSB0" er in staan.

[Hannibal2206]

root@ubuntu:~# modprobe -v usbserial

insmod /lib/modules/2.6.20-15-server/kernel/drivers/usb/serial/usbserial.ko

root@ubuntu:~# modprobe -v ftdi_sio

insmod /lib/modules/2.6.20-15-server/kernel/drivers/usb/serial/ftdi_sio.ko

 

root@ubuntu:~# /var/bin/CCcam.x86 -tvd

17:06:36.689 CCcam: ======================================================================

17:06:36.690 CCcam: starting CCcam 2.0.1 compiled on Jul 7 2007@21:18:19

17:06:36.690 CCcam: ======================================================================

17:06:36.691 CCcam: online using nodeId f44e44b33b163b5d

17:06:36.697 CCcam: create 1 cam device(s)

17:06:36.698 CCcam: readKeyfile: cannot open /var/keys/SoftCam.Key or not found

17:06:36.699 CCcam: readKeyfile: cannot open /var/keys/AutoRoll.Key or not found

17:06:36.699 CCcam: static cw not found or bad

17:06:36.700 CCcam: parsed 0 entries from /var/etc/CCcam.prio

17:06:36.700 CCcam: readProviderfile: cannot open /var/etc/CCcam.providers or not found

17:06:36.748 CCcam: added 1152 channel names from /var/etc/CCcam.channelinfo

17:06:36.749 CCcam: server started on port 12000

17:06:37.191 CCcam: new tcp client from 192.168.1.104

17:06:37.193 CCcam: user monique login attempt from 192.168.1.104

[wian]

De regel in CCcam zou moeten zijn:

SERIAL READER : /dev/ttyUSB0 uniprog

of

SERIAL READER : /dev/ttyUSB0 mouse

of

SERIAL READER : /dev/ttyUSB0 phoenix

 

Alledrie even proberen.

[Hannibal2206]

Ik heb nu een script in /etc/init.d dat hetvolgende bevat:

 

modprobe -v usbserial

modprobe -v ftdi_sio

/var/bin/CCcam.x86 &

 

In dmesg wordt de smartmouse wel herkend, maar ik krijg geen /dev/ttyusb0 device ?? En CCcam ziet hem dus ook niet.

 

Wat mis ik ?

 

[ 29.337115] usbcore: registered new interface driver usbserial

[ 29.337183] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic

[ 29.449082] usbcore: registered new interface driver usbserial_generic

[ 29.449112] drivers/usb/serial/usb-serial.c: USB Serial Driver core

[ 29.512525] drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device

[ 29.512637] usbcore: registered new interface driver ftdi_sio

[ 29.512652] drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver

[Hannibal2206]

ik krijg wel deze devices :

 

han@ubuntu:~$ ls -lai /dev/usb*

6772 crw-rw---- 1 root root 254, 0 2007-08-04 01:52 /dev/usbdev1.1_ep00

6786 crw-rw---- 1 root root 254, 1 2007-08-04 01:52 /dev/usbdev1.1_ep81

7017 crw-rw---- 1 root root 254, 2 2007-08-04 01:52 /dev/usbdev1.2_ep00

7028 crw-rw---- 1 root root 254, 4 2007-08-04 01:52 /dev/usbdev1.2_ep02

7021 crw-rw---- 1 root root 254, 3 2007-08-04 01:52 /dev/usbdev1.2_ep81

[dolphs]

ik ga binnenkort meedenken, heb een USB smartmouse van WB hier liggen <img src="/forums/images/graemlins/xyxthumbs.gif" alt="" />

[dolphs]

@hannibal - welke productId en VendorID heb jij voor de smartusb? Doe eens een lsusb, dan krijg ik: Bus 001 Device 004: ID 0403:6001 Future Technology Devices International, Ltd 8-bit FIFO. Mocht je iets krijgen als Bus 001 Device 001: ID , 104f:0002 (kijk even niet precies naar ID maar dus wel als er niets achter staat) dan kan ie de reader niet identificeren. Prog 'm om met MProg 3.0 naar 0403 en 6001 dat is het simpelste denk ik, of je moet een kernel willen hacken (ook leuk hoor en dan juiste identificatiestring meecompilen, staat allemaal utigelegd in Carsten's file). MAAR ... Ik heb op dit moment mijn digitenne kaartje ( conax 3580 ) eraan hangen en krijg wat ik wil zien met CCcam:

 

root@develop:/var/etc# ./CCcam -d

17:37:30.939 CCcam: ======================================================================

17:37:30.940 CCcam: starting CCcam 2.0.3 compiled on Aug 1 2007@22:36:07

17:37:30.940 CCcam: ======================================================================

17:37:30.941 CCcam: online using nodeId 691bb37d1a3a4c0

17:37:30.945 CCcam: create 1 cam device(s)

17:37:31.160 CCcam: calculated EGT: 0 us

17:37:31.160 CCcam: conax card found

17:37:31.425 CCcam: card added to broker with caid b00

17:37:31.426 CCcam: readKeyfile: cannot open /var/keys/SoftCam.Key or not found

17:37:31.426 CCcam: readKeyfile: cannot open /var/keys/AutoRoll.Key or not found

17:37:31.426 CCcam: static cw not found or bad

17:37:31.427 CCcam: parsed 0 entries from /var/etc/CCcam.prio

17:37:31.427 CCcam: readProviderfile: cannot open /var/etc/CCcam.providers or not found

17:37:31.427 CCcam: readChannelList: cannot open /var/etc/CCcam.channelinfo or not found

17:37:31.427 CCcam: server started on port 12000

 

 

NB nog wel even " SERIAL READER : /dev/ttyUSB0 " in de Config zetten, probeer eens MET en ZONDER de optie mouse of phoenix ligt er even aan welke smartcard en stand smartmouse ( volgen we nog? ).

 

Nu verder met smusbutil aan de slag gaan om snelheid om te kunnen zetten, ik zou graag een kaartje willen hebben nu welke >3,58 draait dan kan ik zien of dat ook wordt gepakt maar zal wel niet want heb op NSLU2 (met openslug) ook problemen om smartmouse in een hogere stand te krijgen.

 

Verder nog even stappenplannetje wat ik tot nu toe heb gedaan ( uit hoofd kan zijn dat ik iets vergeet ):

 

Basis Ubuntu 7.04 server geinstalleerd, dus 32 bits in VMWare

login met normale user

sudo –s

vi /etc/apt/sources.list (# alle cdrom commenten)

apt-get update

apt-get upgrade

apt-get install openssh-server unzip libc6-dev bind-dev libusb-dev libftdi-dev make gcc

 

Open SSH sessie en log in naar IP adres van Ubuntu 7.04

Volg deze handelingen uit om CCcam te kunnen starten

cd /tmp

wget -P . http://weetikveelwaar.hu/dbw/extra/CCcam.zip

unzip CCcam.zip

cd /var

mkdir keys

mkdir etc

cd etc

Kopieer nu de twee relevante bestanden

cp /tmp/CCcam.x86 CCcam

cp /tmp/CCcam.cfg

 

Om CCcam te starten executable maken door " chmod u+x CCcam (of chmod 100) " en daarna ./CCcam –d

 

Als er geen library problemen zijn dan door naar hieronder anders nog even juiste lib downloaden met apt-get install, kan zijn dat ik er eentje heb gemist hierboven

 

insmod /lib/modules/2.6.20-15-server/kernel/drivers/usb/serial/usbserial.ko

insmod /lib/modules/2.6.20-15-server/kernel/drivers/usb/serial/ftdi_sio.ko

wget –P . http://sitevaninfinityusb.dk/files/smusbutil.tar.bz2

tar xvjf smusbutil.tar.bz2

cd smusbutil

vi smusbutil.c en pas dit aan naar: 0x0403, 0x6001

make

mv smusbutil /usr/bin/smusbutil

 

smusbutil phoenix 3580, etc dat zou nu moeten werken en dan kan je ook de snelheid veranderen. Als ie geen card reader vindt dan klopt de identificatie (product/ vendor) niet. Het lijkt een hoop werk maar valt reuze mee, ik zeg dus nog niet dat ik 'm op hogere snelheid werkend heb want ik zit zonder Irdeto II kaart <img src="/forums/images/graemlins/frown.gif" alt="" />

[Hannibal2206]

@Dolphs

 

Ik krijg idd de "verkeerde" Id string

 

han@ubuntu:~$ lsusb

Bus 001 Device 002: ID 104f:0002

Bus 001 Device 001: ID 0000:0000

 

Heb je een link voor de tools om dit om te zetten onder XP ?

[Hannibal2206]

opgelost; zie http://www.sat4all.com/forums/showflat.p...rue#Post1417992