[Nokia] dvb2000 emu met amon v5.1 (wanissa van amonn) 2002

[Gast]

Hallo satfreek, hier is nu de dvb2000 emu met amon v5.1 (wanissa van amonn)met twee firmware

op een eeprom 27sf512 voor irdeto en seca emulatie ,only voor de nokia 9200 of 9500.

 

Of what consists the new hardware change of the Cam for Wanissa:

The change on the Cam serves for arranging 2 firmwares on the same eeprom, it

is as if we had two Cam in one.

The first Cam is the normal Cam erdito that uses the SC erdito to get the

Control Word from it and send them to SAS for the descrambling process of the MPEG

This version is Amon5.1 that to difference from it's preceding Allsas4.0, have the

following advantages:

1.Removed all the non routines that not needed and the firmware have been

realized completely in Asm and without the implementation of the second seriale

for the use of CamExplorer, therefore it is a lot more fast in the change channel and the

communication with the SC.

2.Eliminated the train of impulses on the line Ecm Interrupt produced by the

SAS when it passed over the seca or Viace.., therefore less overheating of the

chip most precious SAS, temperature almost zero.

3.Eliminated the part that writes in continuation the small eeprom 24c16

that in the preceding versions causes the block of the dispatch of the Ecms

to the SC and it was necessary to mend the Cam using the WallBanger with it

inserts and the Season unthreads to resuscitate the Cam.

4.It can be used with an any dvb2000, italtel,FTAx.x or other decoders irdeto.

 

 

Disadvantages:

1.Secondary serial disabled , therefore no CamExplorers.

2.Removed the routine of the ECM_PID hunter that served x the italtel on the

providers of Multi Ident fines tip D -, Taq...

 

To use Amon5.1 any change on the Cam is not needed if is not wanted

to have also the Wanissa on the same Eprom, eventhough the Wanissa is present

however inside the eprom in the case that one should decide to make the change in the

future.

If instead it is predisposed for the HW change,is necessary to put the Dip Switch in

the position number 1, that is the position ALLSAS, see the scheme of the

change.

 

Instead The second Cam is the more desired of everybody, it is the mythical

Wanissa with all her advantages:

1.No use of SC.

2.Fast in the change channel.

3.Temperature zero on the SAS.

4.To firmware modifiable from DVBK via SCSI or Seriale, also from CamExplorer

via RS232 of the same Wanissa.

 

 

Disadvantages:

1.Being forced to make the change HW on the Cam............

2.Used only with the DVBKemu.

Any other dvb2000, Italtel or other decoders erdito will not work.

It works only with the MM9500/9200 DVBKemu.

 

To use the Wanissa is necessary to put the Dip Switch in the position 3, that

is Wanissa with SBR.

The position 2, Wanissa without SBR not to be ever used, at least for the moment

otherwise either the Cam and the Decoder will hang.

 

 

 

Groeten

 

<img src="/ubbthreads/images/icons/wink.gif" alt="" /> <img src="/ubbthreads/images/icons/wink.gif" alt="" /> <img src="/ubbthreads/images/icons/wink.gif" alt="" /> <img src="/ubbthreads/images/icons/wink.gif" alt="" /> <img src="/ubbthreads/images/icons/wink.gif" alt="" />