locutus Geplaatst: 4 november 2002 Delen Geplaatst: 4 november 2002 Ben hierop gebotst bij huts. Heeft iemand ervaring met deze update en de mogelijkheden/beperkingen ervan. Thanx DM920UHD ET9000 Yupsikidee, t'is weer zwart op tevee. Link naar reactie Delen op andere sites Meer opties om te delen...
Littlesat Geplaatst: 5 november 2002 Delen Geplaatst: 5 november 2002 Je kunt dan settings upload/downloaden met het Tux programma en met de virtuele afstandsbediening op je PC via RS-232 werken. Niet veel bijzonders dus. Wordt eigenlijk tijd dat er ook Tux +20 voor de andere Humaxen zoals onze 5300 komt!!!!!!!!!1 Binnenkort is bijna alles in MPEG4 bij CanalDigitaal... je SD ontvanger kan dus in de Kliko Link naar reactie Delen op andere sites Meer opties om te delen...
digiflo Geplaatst: 5 november 2002 Delen Geplaatst: 5 november 2002 Ik heb de tuxon 2.0 op mijn 5300 gezet en het werkt uitstekend. Natuurlijk zonder het embedded via cam. Link naar reactie Delen op andere sites Meer opties om te delen...
locutus Geplaatst: 5 november 2002 Auteur Delen Geplaatst: 5 november 2002 "Natuurlijk zonder het embedded via cam" <img src="/ubbthreads/images/graemlins/confused.gif" alt="" /> Hiermee bedoel je dat de interface (menu ed) werkt, maar dat de codering beperkt blijft tot viaccess? DM920UHD ET9000 Yupsikidee, t'is weer zwart op tevee. Link naar reactie Delen op andere sites Meer opties om te delen...
digiflo Geplaatst: 6 november 2002 Delen Geplaatst: 6 november 2002 Het viacess cam werkt niet met de toh 2.0. Viacess decodering is dan enkel mogelijk met freecam of magic modul. Dus als je enkel met viacess werkt zou ik niet veranderen. Link naar reactie Delen op andere sites Meer opties om te delen...
Gast Geplaatst: 6 november 2002 Delen Geplaatst: 6 november 2002 Sorry maar deze patch wat houdt die precies in? Wat voor voordelen heeft ie tov de normale software? Chris Link naar reactie Delen op andere sites Meer opties om te delen...
mmm Geplaatst: 6 november 2002 Delen Geplaatst: 6 november 2002 Hoi Digiflo, je brengt me op een idee <img src="/ubbthreads/images/graemlins/blush.gif" alt="" /> Op jou 5300, met inmiddels firmware voor de 5400 +CAM ToH2.0, kun je daar net zo goed de ECM's en al die andere informatie zien als je op 't "?"-knopje drukt? Groetjes, <img src="/ubbthreads/images/graemlins/cool.gif" alt="" /> Link naar reactie Delen op andere sites Meer opties om te delen...
locutus Geplaatst: 6 november 2002 Auteur Delen Geplaatst: 6 november 2002 Mischien een beetje mis uitgedrukt. Eigenlijk bedoelde ik: Kun je via de embedded cam ook andere coderingen decrypteren (mits je een software update gedaan hebt), of blijft dit beperkt tot viaccess. Thx DM920UHD ET9000 Yupsikidee, t'is weer zwart op tevee. Link naar reactie Delen op andere sites Meer opties om te delen...
digiflo Geplaatst: 6 november 2002 Delen Geplaatst: 6 november 2002 @mmm Ik heb eer een nieuwe PMC Tabel ingestokken. Je kunt ze raadplegen en veranderen, maar zonder resultat. Ik denk dat dit enkel bedoeld is voor het embedded irdeto cam van de 5400. Dus geen TPS, wel MV. Maar anders heb je dezelfde mogelijkheden als met een 5400. @locutus het embedded viacess cam is uitgeschakeld een is dus ook niet gepatcht. @chris ******************************** * TuxOnHumax proudly presents: * * * * +CAM ToH 2.0 * ******************************** --------- |Preface| --------- With this version it is necessarily to used a version of the program HRC > = 2,4 and Setview > = 2,0. For editing the PMC a new version of the program PMC-Edit is necessary too. It is not allowed to change the ToH firmware in any way without our Agreement. For adapted language versions, please get in contact with us under http://tuxonhumax.berlios.de/board/index.php . ---------- |Security| ---------- In order to ensure that the enclosed HDF file is an original ToH firmware, you only should use the program HU (Humax Uploader) for flashing the humax. The firmware consists of the files HIC-10500+CAM+ToH20.hdf and HIC-10500+CAM+ToH20.tux . Both files are necessary for an examination by HU for the protection from fakes, which could destroy the Humax. The version is identified while loading in HU. ---------------------------- |New features in version2.0| ---------------------------- Macro mode implementation with Humax remote control Automatic 16:9 or 4:3 format change-over for 16:9 televisions Adjustable time offset per channel PMC entries can be assigned to an antenna id +CAM functionality can be switched off PAL/NTSC support Extended film info menu -16:9 flag -long filminformation -filminformation on all Premiere Directchannels -clearer film detail display ToH QME Module -info menu -internal view of data -parser ToH EPG Module -extended EPG display -settingseditor -PMCT editor -configuration menu ---------------------------------- |Documentation of the innovations| ---------------------------------- ----------- |Macromode| ----------- There is a new mode in the firmware, which can be activated or deactivated with the TV/Sat key on the remote control. According to standard this mode is active. When pressing the key a green "M" is displayed for macro mode on and a red "M" mode is deactivated. The original function of the TV/Sat key is obtained by pressing the key two times in a short time. In the macro mode it is possible set the keys of the remote control with own commands or command chains. The programming of these macros happens with the program HME (Humax macro editor). With this program you can test and set the macros, with attached RS232 zero-modem cable from the PC to the Humax, for a durable allocation with the occupied functions a HDF file is produced, which can be downloaded with HU. There are two macros defined in the act, the Firmware reserves on the keys "?" and "EPG". With these keys two new ToH modules can be called (ToH QME Module und ToH EPG Module). --------------------------------------------------------------- |Automatic 16:9 or 4:3 format change-over for 16:9 televisions| --------------------------------------------------------------- In the firmware an automatic format recognition is implemented, these recognizes the sent format (16:9 or 4:3) and switches an attached 16:9 television into the correct format. So that this function functions perfectly, the receiver must be set to "16:9" "Full" under A/V output settings. The further control is then taken over by the Humax. With the configuration menu in the ToH EPG Module (see below) you can switch on/off the automatic recognition. According to standard it is switched on. Note: So that the receiver can control the television, a full-wired scart-cable between receiver and TV must be used. ------------------------------------ |Adjustable time offset per channel| ------------------------------------ Foreign channels are sending a systemtime over the DVB stream, which has a time offset to the local time (for example Premiere to Stream). If you set the time offset in the original menu for the time settings to the correct shift for the local time, the time from the foreign channel is wrong. With this version it is possible to set the time offset for each channel relative to global time offset. This takes place similarly as you switch off Dolby digital for some channels over the PMCT (see PMCT entries under ToH EPG Module, column "TO" for time offset). ---------------------------------------------- |PMC entries can be assigned to an antenna ID| ---------------------------------------------- In the past it could lead to problems, if on different satellites providers use the same service-id. In the PMCT distinct select of the channel was possible. Now the clarity over antenna-id and service-id was extended into the PMCT. ---------------------------------------- |+CAM functionality can be switched off| ---------------------------------------- The +CAM functionality of the internal CAMs can be switched off for individual channels. This is done via registering an CA-ID of "FFFF" for the appropriate entry into the PMCT. So the CA-ID is only evaluated by an external CI module. ------------------ |PAL/NTSC support| ------------------ With the current version an automatic recognition of NTSC for our "DX'ler" friends is implemented. For NTSC channels the solution is set to 704*480 and 30Hz, so the channels can be shown correctly and without disturbances, if your TV does support NTSC. Besides most of the important screen insertions are recomputed, because of the smaller number of lines. A 100% adjustment of all menus is too complex, therefore some menu data are lost downward. The recognition can be switched on/off in the config menu in the ToH EPG Module (see further below). With PAL transmissions the format is switched back to PAL automatically. ------------------------- |Extended film info menu| ------------------------- The info box, which appears while switching the programs or through pressing the red "i" key on the remote control, was transformed. With 16:9 transmissions an appropriate symbol apart from the time appears. On transmitters with short category display (e.g. comedy) the storage location category is used to show a not shorten film title. These most not shorten film titles are also shown in the ToH EPG Module. On each premiere direct channel the film info is shown and not only on those with an "E". So that this functions will work, you have to switch once to a direct channel with "E" or another channel, which sends on this transponder. One of the channel this works on are: PremNostalgie, PremSerie, Krimi&Co, DiscoveryChannel or Sport2. The data for the others direct channels will be buffered thereby, while on the transponder with the direct channels without "E" no EPG information is sent. The film detail box, which appears if you press "?" on the remote control, during the info box is displayed, is shown in a clearer format. ---------------- |ToH QME Module| ---------------- By pressing the key "?" on the remote control in macro mode, you wil get into the ToH QME Module. This menu is partitioned into five coloured differentiated register maps, which you can select through pressing the accordingly colored key on the remote control. Appropriate paging through the menus is likewise possible by pressing the cursor keys right/left beside the "OK" key. In the red menu all channel relevant data is clearly listed. In the green menu the current solution is shown, as well as the signal strength and -quality. The audio information of the current channel is displayed too. While listening dolby digital these information are empty. In the yellow menu your own PMCT is shown, as well as contents of the conditional access table (CAT) and the programm map table (PMT). The sub functions on the left side , can be selected with the appropriate numbers on the remote control. If the announcement of the information is longer than a page, then page by page scrolling is possible with the cursor keys up/down below the "OK" key. On the blue side a parser is displayed, which translates the PMT. With the cursor keys up/down it can be scrolled page by page. The white menu contains general informations and a small "James Bond" secret :-D. ---------------- |ToH EPG Module| ---------------- Into the ToH EPG menu you get by pressing the key "EPG" in the macromode on the remote control. This module is divided into four submenus, you can select each of them by pressing the cursor keys right/left beside the "OK" key on the remote control. Under EPG the most unshorten film titles (see extended film info menu) with the weekday and the starting times are shown. The actual running channel is white emphasized. With the cursor keys up/down, over and under the "OK" key, you can scroll the pages. This applies also to all other sub menus in this module. During the using of the EPG zapping with P+ and P- is possible. In the submenu settings all channel settings are displayed, the actual received channel is white emphasized. By pressing the "OK" key the settings data can be changed. The current channel name will get red, now you can select the channel you want to change with cursor keys up/down. With the cursor key right the entry which you want to change can be selected and changed. If you select the antenna/frequency you only can select between transponders which are already existing, a transponder search is not possible. The changes are stored through pressing the "OK" key, to reject the changes press the "EXIT" key on the remote control. All made changes in the settings are stored directly into the flash and remain also after switching off the receivers. In the submenu PMCT the adjusted entries are shown and can be changed and extended for test purposes. The PMCT cannot be flashed at present while it is in use, therefore changes and extensions are valid only up to next switching off. This should be sufficient for testing entries, durable changing of the PMCT is possible with the program PMC-Edit. If an entry is used for the actual received channel, the entry is white emphasized. Changing of the entries is possible by pressing the "OK" key on the remote control. A red line appears, and with the cursor keys up/down the line which you want to chang can be selected. With the cursor key right the appropriate value can be selected and changed afterwards. Hex values can be entered while pressing the following keys "Mute"=A, "RED"=B, "GREEN"=C, "YELLOW"=D, "BLUE"=E and "WHITE"=F on the remote control. The changes can be stored by pressing the "OK" key (like said only up to switching off). If you want to rejected the changes, this is done by pressing the "EXIT" key on the remote control. Into the PMCT some new fields were added "Ant ID" and "TO". With "Ant ID" the antenna you want to use is specified, on which the adjusted service id is to be used (see PMC entries can be assigned to an antenna id). With the field "TO" a time offset for the selected channel, relative to the generally used time in hours can be set (Adjustable time offset per channel). With selecting the point with the cursor a positive or negative time offset can be set with cursor keys up/down. If you want to switch off the +CAM functionality for a special channel, you have to enter "FFFF" as the CA-ID the channel selected by the service-id. This is intended for simultaneous use with external CI modules. If the entry of the actual received channel is selected by pressing the "OK" key, right of the line all actual sent entries will be appear for the entry. If you press the cursor keys up/down after selecting the CA-ID, the possible entries are set automatically. It is likewise possible to add new entries into the PMCT for test purposes. To do this you have to go to the last page of the PMCT and press "OK". A red line appears, now you must scroll up to the last entry of the list and press cursors down one more time. An entry with the actual data of the current channel is added and can be edited. All sent values are shown on the right side of the entry. An added entry can be deleted by selecting an ant-id of "0" (then DELETE will be displayed instead) and confirm it by pressing "OK". With the submenu "CONFIG" some ToH specific functions can be adjusted. With the point "macro mode on Startup" you can adjust whether the macro mode is active when you switch on the receiver. It can be switched off at any time by pressing the "TV/SAT" key (see macro mode). With the point "Auto 16:9/4:3 - Switch" you can steer whether the automatic format change-over for 16:9 televisions should be active on startup or not (see automatic 16:9 or 4:3 format change-over for 16:9 televisions). The point "Auto NTSC/PAL - Switch" controls the automatic recognition and change-over of NTSC channels and the change-over to NTSC with 30HZ (see PAL/NTSC support). ****************************************************** Have fun with the +CAM ToH 2.0 wishes you * * HUMI_USER, Padawan, Planet Hemp, QME5400, Undici77 * * and the rest of the TuxOnHumax team * ****************************************************** Link naar reactie Delen op andere sites Meer opties om te delen...
mmm Geplaatst: 6 november 2002 Delen Geplaatst: 6 november 2002 Hoi Digiflo, ja dat van die PMCT, dat zat er wel in. Die tabel is volgens mij door PH in het leven geroepen om zijn +CAM te ondersteunen. Daar heb je dus de embedded Irdeto CI voor nodig. Maar de info over de ECM's, die interesseren me nog. Kun je daar nog wat over zeggen. Dus werkt 't "?"-knopje wel? @Locotus, misschien voor alle duidelijkheid: Digiflo bedoelt dat de Embedded Viacam HELEMAAL is uitgeschakeld. Misschien zelfs wel hardwarematig losgekoppeld, dat kan ook nog. In ieder geval kun je er geen Viacces-kaart meer mee gebruiken. Groetjes, <img src="/ubbthreads/images/graemlins/cool.gif" alt="" /> Link naar reactie Delen op andere sites Meer opties om te delen...
digiflo Geplaatst: 6 november 2002 Delen Geplaatst: 6 november 2002 @mmm het menu is hetzelfde als van de 5400, dus ook als je de ? toets gebruikt, maar bij 'emc' en 'ca id' staat niets vermeld. Werkt waarschijnlijk enkel met interne irdeto cam in de 5400. Het interne viacess cam hoeft niet losgekoppeld te worden, als je hem wilt patchen. Ik zou zeggen: uitproberen. Je kunt altijd nog terugpatchen. De sys-id moet wel verandert worden, dat heb ik met hdf-tool gedaan. Groetjes Digiflo Link naar reactie Delen op andere sites Meer opties om te delen...
mmm Geplaatst: 6 november 2002 Delen Geplaatst: 6 november 2002 @Digiflo, ik heb 't even uitgeprobeerd. Interne CAM inderdaad gewoon laten zitten. Helaas geen CA-ID en ECM-ID. Het blauwe Tab-blad was helemaal leeg, en het gele tabblad liet alleen de ingevoerde PMC-tabel zien. Wel jammer, maar zoals je zegt, zal dit dan inderdaad uit de CAM komen. Dat van die CA-ID kan ik nog wel begrijpen, maar van de ECM is het echt jammer, ik dacht dat iedere decoder dat gebruikte. Misschien is die wel het makkelijkst uit de CAM te halen??? Was toch leuk <img src="/ubbthreads/images/graemlins/tongue.gif" alt="" /> Nog bedankt voor de tip, ben weer wat wijzer. Groetjes, <img src="/ubbthreads/images/graemlins/cool.gif" alt="" /> Link naar reactie Delen op andere sites Meer opties om te delen...
Littlesat Geplaatst: 7 november 2002 Delen Geplaatst: 7 november 2002 Hoe zet je de Tux 2.0 op de Humax 5300.... gewoon doen? Binnenkort is bijna alles in MPEG4 bij CanalDigitaal... je SD ontvanger kan dus in de Kliko Link naar reactie Delen op andere sites Meer opties om te delen...
digiflo Geplaatst: 7 november 2002 Delen Geplaatst: 7 november 2002 @littlesat Maak hiervan een batch file, wanneer de sys Id van je 5300 dezelfde is en kopieer de tux 2.0 en de .bat naar c:. hdftool u HIC-10500+CAM_ToH20.hdf del hdfbin-0-000000.raw del hdfbin-3-006000.raw hdftool c newhic.hdf -id1=0017.0000 -id2=0017.0600 del hdfbin-1-000000.raw del hdfbin-1-140000.raw del hdfbin-1-150000.raw del hdfbin-1-160000.raw del hdfbin-1-170000.raw del hdfbin-3-010000.raw del HIC-10500+CAM_ToH20.hdf del HIC-10500+CAM_ToH20.nfo cls Groetjes Digiflo HIC-10500+CAM_ToH20= naam van de soft die je wilt veranderen newhic= nieuwe soft Link naar reactie Delen op andere sites Meer opties om te delen...
Littlesat Geplaatst: 7 november 2002 Delen Geplaatst: 7 november 2002 Bedankt voor de batchfile....... En werkt het dan ook met een Freecam2-019? Binnenkort is bijna alles in MPEG4 bij CanalDigitaal... je SD ontvanger kan dus in de Kliko Link naar reactie Delen op andere sites Meer opties om te delen...
Aanbevolen berichten
Maak een account aan of log in om te reageren
Je moet een lid zijn om een reactie te kunnen achterlaten
Account aanmaken
Registreer voor een nieuwe account in onze community. Het is erg gemakkelijk!
Registreer een nieuwe accountInloggen
Heb je reeds een account? Log hier in.
Nu inloggen