reptovis Geplaatst: 2 juli 2003 Delen Geplaatst: 2 juli 2003 Beste PVR-8000's Niet getreurd meer, want de E-AC error is verleden tijd. Ik heb hetzelfde probleem gehad na het inzetten van de zenderlijst! <img src="/ubbthreads/images/graemlins/grin.gif" alt="" /> Maar na de melding hiervan bij Humax kreeg ik wonder boven wonder een e-mail uit Ierland terwijl Duitsland mij een mail stuurde dat je er niets aan kon doen. Het probleem was direct te verhelpen door eenvoudig een prog'je ophalen via het adres van de ontvangen mail en daarmee de originele setting er weer in te blazen! <img src="/ubbthreads/images/graemlins/xyxthumbs.gif" alt="" /> Je kunt gewoon een o-modemkabel gebruiken om de setting erin te krijgen! <img src="/ubbthreads/images/graemlins/tongue.gif" alt="" /> Ik geef jullie de mij toegezonden mail en je kunt bij mij de originele setting via mij krijgen, nadat je mij ff een mailtje stuurt. Helaas was de bijlage te groot om deze hier te plaatsen. Ook inpakken lukt niet. Mijn e-mailadres is Han.W@Tiscali.nl <img src="/ubbthreads/images/graemlins/anoniem.gif" alt="" /> P.s. Het blijkt dat de link niet meer werkt, dus dan stuur ik het programma ook even mee <img src="/ubbthreads/images/graemlins/biggthumpup.gif" alt="" /> Vr. Gr. Reptovis De mij toegezonden mail was: Dear Sir, Thank you for your HCSA request. Please find attached the software you require for the PVR 8000; you will need to download this software to your receiver to resolve the E-AC error. You will also need to download a software download tool (WDN4OAK) and install this on your PC, then connect the PC to your receiver with a NULL modem cable (9 PIN Female to 9 PIN Female with Pins 2 and 3 crossed). You will also find instructions and a diagram of the cable needed on this site http://www.humaxdigital.com/support/support_down7.htm. To connect the receiver to your PC, you will need a NULL Modem cable. The upgrade procedure is as follows: - Connect the power cable to the IRD and ensure that it is in Standby mode. - Connect the Null Modem cable (see below) from the PC to the IRD. - Start the Wdn4oak application. - In Wdn4oak, select the COM port and Baud Rate you wish. - Now select the HDF file you want to download. To do this please click on the Folder icon. - A new window will now appear. Here you can navigate around your folders. Select the drive and then folder that the HDF file is located. - Select the file and click OK. - To begin the download, click the "Go" button. - You will now see the message 'waiting for Humax'. - Switch on you IRD (using the Standby key), the downloading process will now begin. - Please wait until you see 'End' displayed on the IRD front panel, or the Download Complete message appears on the TV. - Restart IRD. http://www.humaxdigital.com/support/support_down7.htm Null Modem cable used for the upgrade requires the following Pin connections: Pin 2 to Pin 3 Pin 3 to Pin 2 Pin 5 to Pin 5 If you require any further assistance please do not hesitate to contact me. Best Regards Michael Caughey Customer Services Engineer Humax Electronics Co. Ltd. Unit 1 Jubilee Road Newtownards Co Down N. Ireland BT23 4YH <img src="/ubbthreads/images/graemlins/lezen.gif" alt="" /> Gewoon even prog'je ophalen en setting erinblazen dus <img src="/ubbthreads/images/graemlins/cool.gif" alt="" /> Veel succes! Groeten Han alias Reptovis Dreambox 7000S + Maxtor 300GB + Quattro 0.3dB Lnb + Triax 110 + Sg2100/Topfield 5500 + Maxtor 300GB + Dual Lnb + Triax 90 + Sg2100 + Aston 1.07 + Xcam/Humax 5400 + MM/Reptielen/Vissen/Honden Link naar reactie Delen op andere sites Meer opties om te delen...
Gast Geplaatst: 2 juli 2003 Delen Geplaatst: 2 juli 2003 Bedankt Han. Dit was het verlossende stukje software wat ik miste..... <img src="/ubbthreads/images/graemlins/biggthumpup.gif" alt="" /> <img src="/ubbthreads/images/graemlins/biggthumpup.gif" alt="" /> <img src="/ubbthreads/images/graemlins/biggthumpup.gif" alt="" /> <img src="/ubbthreads/images/graemlins/grin.gif" alt="" /> Link naar reactie Delen op andere sites Meer opties om te delen...
Gast Geplaatst: 3 juli 2003 Delen Geplaatst: 3 juli 2003 dank je grtz ray <img src="/ubbthreads/images/graemlins/xyxthumbs.gif" alt="" /> <img src="/ubbthreads/images/graemlins/biggthumpup.gif" alt="" /> Link naar reactie Delen op andere sites Meer opties om te delen...
Aanbevolen berichten
Maak een account aan of log in om te reageren
Je moet een lid zijn om een reactie te kunnen achterlaten
Account aanmaken
Registreer voor een nieuwe account in onze community. Het is erg gemakkelijk!
Registreer een nieuwe accountInloggen
Heb je reeds een account? Log hier in.
Nu inloggen